Side Sill Panels

Heating tube inside side sill left or right.

This is a bespoke restoration product, you can not buy this from Porsche !

Fits:
Porsche 911/912 1965-68 SWB cars

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

91150340000

The product you are viewing cross references to these numbers

Heating tube inside sill (left/right).
This Heater Tube Inside Sill is a Genuine Porsche OE component designed to route heated air through the inner sill section of classic air-cooled Porsche 911 models from 1969 to 1989. The heater tube carries warm air produced by the engine’s heat exchangers through the sill cavity toward the cabin ventilation system.

Fits:
Porsche 911 1969 - 1989

Diagram ref no 15

Function: Installed inside the vehicle’s sill structure, the tube forms a critical part of the classic 911 heating system. It channels heated air forward into the cabin ducting, supporting effective interior heating, windscreen demisting, and overall comfort in cooler conditions.

Over time, original heater tubes can degrade due to heat cycles, age, and corrosion, resulting in reduced airflow or heat loss before reaching the cabin. In severe cases, damaged ducting may allow unwanted fumes or debris into the heating system. Replacing the tube with a Genuine Porsche part restores factory heating efficiency, preserves originality, and ensures long-term reliability of the heating system.

Replace this heater tube if you notice:
• Weak or uneven heater output
•  Cracked, brittle, or collapsed ducting
•  Heat loss before air reaches the cabin
•  Unpleasant odours from the heating system
•  During restoration or refurbishment of the sill or heating system

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

91157202502

The product you are viewing cross references to these numbers

Heating tube inside sill, Ø55 mm, length 685 mm.
This heating tube inside sill is a high-quality replacement air-duct tube designed to channel warm air from the exhaust-heated heating system through the sill area of classic Porsche 911 models built from 1969 through 1989 and 356 B/C models. It matches the original part’s fit and performance to maintain proper heating airflow in your vehicle’s cabin.

Fits:
Porsche 356 B/C 1.6 01/1959 - 12/1965
Porsche 911 2.0-3.3 08/1968 - 07/1989
Porsche 912 1.6 01/1965 - 02/1970
Porsche 914 1.7-2.0 01/1969 - 07/1974

Diagram ref no 15

The heating tube directs hot air generated by the engine’s exhaust-heated heat exchangers into the cabin area via the sill ducting. This ensures your classic Porsche’s heater system distributes warmth effectively, improving defogging, defrosting, and passenger comfort in cooler weather.

Function: Installed along the inner sill section, this tube captures heat from the heater system and delivers it through the duct network into the footwell or cabin air distribution points. A properly functioning heater tube helps maintain consistent cabin temperature and prevents heat loss due to damage or age-related degradation of the original ducting.

Over decades of use, original heater tubes can become cracked, brittle, or collapsed, leading to poor airflow, heat loss, or even exhaust gas intrusion into the cabin air system. Replacing the deteriorated tube with an OE Match unit restores effective hot-air distribution, improves cabin comfort and heater efficiency, and keeps the vintage heating system functioning as intended.

Replace this heating tube when you notice:
•  Weak or inconsistent warm air delivery from the heater
•  Deteriorated, cracked, or collapsed heater tubing
•  Excessive heat loss before reaching the cabin
•  Unusual smells from heater ducts (possible leaks)
•  During full heater system or sill restoration work

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

91157202502

The product you are viewing cross references to these numbers

Inner rocker panel, thickness 0.8 mm.



Fits:
Porsche 911 2.0L 01/1963-07/1968

Click 'Zoom in' for large parts diagram.
Diagram ref no 19

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

90150112

The product you are viewing cross references to these numbers

Jack receiver bracket. 



Fits:
Porsche 911 1966-89

Click 'Zoom in' for large parts diagram.
Diagram ref no 9.

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

90150115122GRV

The product you are viewing cross references to these numbers

Jack receiver socket. 



Fits:
Porsche 911 1966-73

Click 'Zoom in' for large parts diagram.
Diagram ref no 10.

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

90150115321GRV

The product you are viewing cross references to these numbers

Oil Pipe inner support bracket for Door Sill Inner Panel. Porsche 911 1966-89, Weld on oil pipe support bracket
6 Required Per car



Fits:
Porsche 911 1966-89

Click 'Zoom in' for large parts diagram.
Diagram ref no 38

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

91150112500GRV

The product you are viewing cross references to these numbers

Rear end cap for wide deco sill / rocker



Fits:
Porsche 911 1969-73 (LWB)
Long Wheel Base Cars

Click 'Zoom in' for large parts diagram.
Diagram ref no 29.

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

90155911

The product you are viewing cross references to these numbers

Rear torsion bar cover with gasket, bracket and nut. 

Sold individually; x2 required per vehicle. 

Fits:
Porsche 911 1965-86
Porsche 911 (930) Turbo 1975-86

Porsche 912 1966-69
Porsche 912E 1976

Diagram ref. 33.

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

90150407900

The product you are viewing cross references to these numbers

Wide rocker deco trim rubber insert for 911S models.

Fits:
Porsche 911 E/S 1969
Porsche 911 1970-173

Diagram ref no 32

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

90155910653

The product you are viewing cross references to these numbers

Side Sill Moulding + Rubber Seal.
Fits: left and right side
Narrow Moulding & Rubber 49" Long

#

Fits:
Porsche 911 1965-73

Click 'Zoom in' for large parts diagram.
Diagram ref no 33

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

90155901122

The product you are viewing cross references to these numbers

Side Sill Moulding + Rubber Seal.
It is a wide type decorative sill panel with a rubber insert that was fitted to the long wheelbase Porsche 911 from 1969 through 1973. The moulding is sized to approximately 59.5″ long and fits either left or right side of the vehicle. This exterior body-trim part sits along the lower rocker (side sill) area below the doors

Fits:
Porsche 911 1969-73 (LWB)
Long Wheel Base Cars

Diagram Ref No. 25

The side sill moulding serves both aesthetic and protective roles on the vehicle’s lower bodywork:
• Protects the rocker panel from minor impacts, road debris, and scrapes
• Accentuates the classic body line, contributing to the vehicle’s period-correct look
• The rubber seal helps bridge the gap between the trim and body, reducing moisture ingress behind the moulding and offering a more finished appearance
• Helps maintain authentic exterior style on restored or well-maintained classic vehicles.

Over decades on the road, original sill mouldings and seals can:
• Fade, crack, or warp
• Lose adhesion or proper fit
• Expose underlying rocker panels to corrosion or damage.

Replacing worn or missing sill trim restores the correct visual line and offers renewed protection for the lower bodywork - especially important on restored vehicles or those being prepared for show-quality presentation.

Replace this side sill moulding if:
•  The original trim is missing, cracked, split, or faded
•   Rubber insert has hardened or detached
•   Re-assembling after bodywork or repaint
•   During a body restoration or concours detailing project

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

90155910553

The product you are viewing cross references to these numbers

Side Sill Moulding + Rubber Seal for ST Look or Wide body (price is EACH)



please note these are longer side sills 62inch, you will need to bend the ends so they fit snug to your wide body arches

Fits:
Porsche 911 1969-73 (LWB)
Long Wheel Base Cars ST Look

Porsche 911 1974-89 ST Look

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

90155910599

The product you are viewing cross references to these numbers

Side Sill Moulding + Rubber Seal

Wide Moulding & Rubber 57.5" Long
Diagram Ref No.25

Fits:
Porsche 911 1968 (SWB)
Short Wheel Base Cars

Fits: left and right side

Fits:
Porsche 911 1969-73

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

90155910552

The product you are viewing cross references to these numbers

Side Sill Moulding - Fits left or right hand side
Sold each

Fits:
Porsche 911 - 1969 to 1973 (LWB)
Long Wheel Base Cars

Diagram ref no 25

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

90155910553

The product you are viewing cross references to these numbers