Moulding and deco trims

Aluminium rivet for front bumper end cap no. 90150515700 and 90150515800.

Fits:
Porsche 911 1969-73

Diagram ref no 41

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

99919010130

The product you are viewing cross references to these numbers

Beading for Bumper end caps 1 metre long (cut to required length)

Fits:
Porsche 911 1965-1977

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

99991108440

The product you are viewing cross references to these numbers

Front bumper chrome moulding with impact rubber.
Narrow type 1/2 inch wide.

The front bumper chrome moulding with impact rubber is a direct-fit decorative and protective trim piece designed for the front bumper of classic Porsche 911 and 912 models (1965 – 73). This narrow-type moulding (½″ width) accurately replicates the factory profile, mounting hole spacing and chrome finish, incorporating a rubber insert to absorb minor impacts and protect the bodywork and finish.

Fits:
Porsche 911 1966 - 1973 (non S and RS)

Diagram ref no 2

•  Position on Vehicle: Front bumper — chrome moulding strip mounted across the bumper face, narrow style (half-inch width) with impact rubber insert.

• Applications: Ideal for restoration or repair of the front bumper trim where the original moulding is worn, corroded, missing or damaged, and where correct period appearance and trim quality matter.

The front bumper moulding serves both styling and practical roles: the chrome trim provides the classic look, while the rubber insert absorbs minor knocks and helps maintain the bumper edge finish. When the original moulding is faded, corroded, loose or missing, you may experience:
•  Visible gaps, mis-alignment or corrosion at the front bumper edge
•  Loss of protective rubber insert leading to chipped paint or damaged bumper edge
•  A less authentic appearance for a period correct vehicle
•  Difficulty sourcing correct mounting points or visible wear.

By replacing it with this moulding, you ensure the trim sits correctly, the finish is factory-correct, the protective rubber is present and the overall front bumper appearance and durability are restored.

When and why to replace:
•  Original moulding shows rust, pitting, bends, missing rubber insert or damaged ends
•  During front bumper replacement, bodywork respray or restoration project
•  Vehicle is being exhibited or resold and accurate period trim is desired
•  Loose or squeaking bumper trim indicates the rubber insert or mounting is worn

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

90150504132

The product you are viewing cross references to these numbers

Front, wide, trim bumper deco rubber insert for 911 1967-73 models with 911S Trim.

Fits:
Porsche 911 1967-73

Diagram ref no 7

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

90150540551

The product you are viewing cross references to these numbers

Front bumper end cap
The front bumper end cap acts as the finishing trim on the left / right outer edge of the bumper assembly. It fills the opening at the bumper corner, helping complete the bumper’s visual profile while protecting the bumper edge from impact, moisture, and debris. Properly installed end caps contribute to a clean, symmetrical appearance and help maintain the aerodynamic shape of the front fascia.

Fits:
Porsche 911 1969 - 1973

Diagram ref no 40

Function:
•  Cosmetic finish: Completes the bumper’s visual lines on the right side
•  Protection: Shields the bumper edge from scraping, chipping, and corrosion
•  Fit and alignment: Helps the bumper sit flush against the body panels
•  Aesthetic continuity: Matches original design so the front end looks factory correct.

Without a properly fitted end cap, the bumper edge can appear unfinished or exposed, and moisture or debris can enter behind the bumper structure, potentially accelerating rust or deterioration.

Front bumper end caps are often overlooked but play an important role in both appearance and protection. Over time, original caps can become:
•  Cracked, warped, or brittle
•  Paint-damaged or faded
•  Missing due to impact
•  Corroded at mounting points.

A worn or missing end cap detracts from the classic Porsche’s front-end appearance and can expose sensitive areas behind the bumper to dirt and moisture. An OE Match replacement restores the correct silhouette and protective function, helping preserve both aesthetics and the structural integrity of the bumper assembly.

When to replace. Replace this bumper end cap if you notice:
•  Visible damage (cracks, dents, splits)
•  Poor fitment or gaps against the bumper
•  Rust or debris behind the original cap
•  Faded or mismatched trim on an otherwise restored vehicle
•  You are completing a bodywork restoration or cosmetic refresh

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

90150515

The product you are viewing cross references to these numbers

Front Bumper End Cap.

Fits:
Porsche 911 1969-73

Diagram ref no 40

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

90150515

The product you are viewing cross references to these numbers

Front bumper moulding with impact rubber (S type - wider)
2 inch wide

Fits:
Porsche 911 1966-73 (S and RS)

Diagram ref no 3

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

90150504551

The product you are viewing cross references to these numbers