Textar

Wheel hub cleaning grinder head. 

Aluminium bell with steel core and 12,5 mm (1/2“) seat for use on pneumatic impact screwdrivers. 
Corrosion between the rim and the wheel hub is removed so torque values can no longer be distorted.
Complete with 1 cleaning disc 

Find out about Textar product verification here

Over the stud wheel hub cleaner set. Textar

Cleaning kit for corroded wheel studs & adjacent hub surfaces

Removes dirt & corrosion & prepares surfaces for correct torque application
Ideal for preparing wheels, hubs and brake discs or drums for re-assembly
Suitable for use with power drill or air impact wrench

Kit contains: 

• Stud cleaner body including velcro pad
• Replacement velcro pads x 2 
• Fine cleaning discs x 5
• Coarse cleaning discs x 5

Find out about Textar product verification here

Brake fluid boiling point tester kit. Textar

Boiling point brake fluid testing is the only test method approved by brake & brake fluid manufacturers

• Increase service revenue & road safety  
• Accurate, reliable & repeatable results
• Operates off the vehicles own 12 volt battery
• Measures up to 320°, suitable for use on all grades of brake fluid including racing fluids
• Multilanguage: English, German, French, Spanish, Italian

Find out about Textar product verification here

Hydra tec lubricant for maintenance work and protection Textar

Available in 75ml Tube or 5ml Sachet

The Advantages of Hydra Tec:

• Facilitates the installation of hydraulic brake components
• Tested compatibility with commercially available braking fluids (DOT3, DOT4, DOT4LV, DOT5.1)
• Free of mineral oils and compatible with EPDM rubber
• In addition, running surfaces are protected against corrosion

Hydra Tec is suitable for lubricating:

• Cylinder running surfaces
• Pistons
• Sealing elements

Application:
Apply a thin layer of Hydra Tec on the marked sections.

Note:
Hydra Tec should be applied thinly and evenly. 
Never use mineral oils or greases as substitutes.
Do not apply the product on friction surfaces of brake pads or brake discs.

Find out about Textar product verification here

Cera-Tec metal free permanent lubricant Textar

For brake systems and is highly temperature-resistant (up to 1,000°C).

Available in 75ml tube and 5ml sachet

The advantages of Cera Tec:
• Non-conductive and contains no solids
• Suitable for ABS
• Facilitates brake installation
• Reduces brake squealing
• Protects against scoring and corrosion
• Free of copper and acids 
• Pressure-resistant / high viscosity

Cera Tec is also suitable for lubricating:• Disc- and drum-brake systems
• Compressors
• Centralised lubrication systems
• Axle bearings
• Chains
• Seat rails
• Sunroof tracks
• Battery terminals

Application:
Apply a thin layer of Cera Tec on the marked sections

Find out about Textar product verification here

Brake fluid DOT 4 20Ltr Textar

Brake fluid is one of the most important fluids in a car as without it, stopping the vehicle safely would be impossible. The Brake fluid transmits the force exerted by the driver on the brake pedal onto the wheel brake. 
To ensure perfect operation of the brakes, the brake fluid must be changed regularly during inspection or maintenance and tested with the correct brake fluid tester.

Brake fluid should be changed every two years. 

The higher the DOT class, the higher the boiling temperature and wet boiling point. Higher DOT classes tend to allow longer maintenance intervals. The DOT standards are based on the American FMVSS-116 standard of the Department of Transportation (DOT).

Boiling Point and Viscosity

Dry Boiling Point - describes the property of the sealed new brake fluid. In this state, the brake fluid is almost anhydrous (substance containing no water). The dry boiling point is usually between 240 and 280°C.

Wet Boiling Point - determines the property of the brake fluid at the end of its life cycle, at a water content of 3.5% the fluid should be replaced. This defined wet boiling point must not be undercut.

Viscosity - describes the flow rate of the brake fluid. The lower the viscosity, the faster the brake fluid flows through the brake system, and the faster the brake signals are transmitted. 

Important Notes
• Brake fluid is poisonous and a hazardous waste.
• Be careful when changing. The fluid weakens paints and plastics.
• It must not come into contact with eyes or skin. Always rinse spilled liquid with water.
• Do not pour the liquid into drinking water or mix with used oil.
• The colour of the brake fluid reveals nothing about its quality.
• Brake fluid should be stored in its original packaging and in a dry, cool and well-ventilated place.

Find out about Textar product verification here

Brake fluid DOT 4 LV (Low Viscosity) Textar.

Textar DOT 4 LV (Low Viscosity) is especially recommended for use in hydraulic brake and clutch systems of vehicles fitted with ESP, ABS and ASR with a high boiling point and outstanding performance at very low temperatures.

DOT 4 LV (Low Viscosity)
Dry Boiling Point ≥ 260° C 
Wet Boiling Point ≥ 165° C 
Viscosity at -40C < 750 mm2 /s

Brake fluid is one of the most important fluids in a car as without it, stopping the vehicle safely would be impossible. The Brake fluid transmits the force exerted by the driver on the brake pedal onto the wheel brake. 
To ensure perfect operation of the brakes, the brake fluid must be changed regularly during inspection or maintenance and tested with the correct brake fluid tester.

Brake fluid should be changed every two years. 

The higher the DOT class, the higher the boiling temperature and wet boiling point. Higher DOT classes tend to allow longer maintenance intervals. The DOT standards are based on the American FMVSS-116 standard of the Department of Transportation (DOT).

Boiling Point and Viscosity

Dry Boiling Point - describes the property of the sealed new brake fluid. In this state, the brake fluid is almost anhydrous (substance containing no water). The dry boiling point is usually between 240 and 280°C.

Wet Boiling Point - determines the property of the brake fluid at the end of its life cycle, at a water content of 3.5% the fluid should be replaced. This defined wet boiling point must not be undercut. <

Viscosity - describes the flow rate of the brake fluid. The lower the viscosity, the faster the brake fluid flows through the brake system, and the faster the brake signals are transmitted. 

Important Notes

• Brake fluid is poisonous and a hazardous waste.
• Be careful when changing. The fluid weakens paints and plastics.
• It must not come into contact with eyes or skin. Always rinse spilled liquid with water.
• Do not pour the liquid into drinking water or mix with used oil.
• The colour of the brake fluid reveals nothing about its quality.
• Brake fluid should be stored in its original packaging and in a dry, cool and well-ventilated place.

Find out about Textar product verification here

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

95006

The product you are viewing cross references to these numbers

Brake fluid DOT 4 



Brake fluid is one of the most important fluids in a car as without it, stopping the vehicle safely would be impossible. The Brake fluid transmits the force exerted by the driver on the brake pedal onto the wheel brake. 

To ensure perfect operation of the brakes, the brake fluid must be changed regularly during inspection or maintenance and tested with the correct brake fluid tester.

Brake fluid should be changed every two years. 

The higher the DOT class, the higher the boiling temperature and wet boiling point. Higher DOT classes tend to allow longer maintenance intervals. The DOT standards are based on the American FMVSS-116 standard of the Department of Transportation (DOT).

Boiling Point and Viscosity

Dry Boiling Point - describes the property of the sealed new brake fluid. In this state, the brake fluid is almost anhydrous (substance containing no water). The dry boiling point is usually between 240 and 280°C.

Wet Boiling Point - determines the property of the brake fluid at the end of its life cycle, at a water content of 3.5% the fluid should be replaced. This defined wet boiling point must not be undercut. 

Viscosity - describes the flow rate of the brake fluid. The lower the viscosity, the faster the brake fluid flows through the brake system, and the faster the brake signals are transmitted. 

Important Notes
• Brake fluid is poisonous and a hazardous waste.
• Be careful when changing. The fluid weakens paints and plastics.
• It must not come into contact with eyes or skin. Always rinse spilled liquid with water.
• Do not pour the liquid into drinking water or mix with used oil.
• The colour of the brake fluid reveals nothing about its quality.
• Brake fluid should be stored in its original packaging and in a dry, cool and well-ventilated place.

Find out about Textar product verification here

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

95002

The product you are viewing cross references to these numbers