OE Match

Transmission case rubber mount.
The transmission mount helps hold the manual gearbox in place, ensuring it stays securely positioned under side load and torque. It also absorbs engine and drivetrain vibration, preventing it from transmitting into the cabin or other chassis components. By maintaining proper transmission alignment, it supports smooth gear shifting and reduces stress on linkage and drivetrain parts.

Fits:
Porsche 356 1.1-2.0L 08/1950 - 04/1965

Diagram ref no 49

Installed between the transmission housing and the vehicle’s chassis or subframe, this mount:
•  Secures the manual transmission in its correct position
•  Dampens vibration and noise from the drivetrain
•  Helps maintain accurate drivetrain alignment
•  Reduces wear on surrounding mounts, brackets, and hardware

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

5192009

The product you are viewing cross references to these numbers

Brake master cylinder with brake fluid tank. (19.05mm).



Fits:
Porsche 356 1.1-1.5L 01/1950-12/1955
Porsche 356A 1.5L 01/1955-12/1961
Porsche 356B 1.6L 01/1959-12/1963

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

35642020

The product you are viewing cross references to these numbers

Front bonnet in aluminium. For racing cars only - fragile aluminium material, total weight 5.1 kg
The frame and outer skin are made out of aluminium. Long Nose Bonnet



Fits:
Porsche 911 1969-73

Click 'Zoom in' for large parts diagram.
Diagram ref no 1

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

90151101024GRV

The product you are viewing cross references to these numbers

Reconditioned replacement speedo.

Completely rebuilt speedometer for KM/H cars, this item is sold as an exchange item so you will need to send your old unit back to us for the surcharge refund.

Fits:
Porsche 911 1970-73

PLEASE NOTE:

• The surcharge for this reconditioned part will be refunded when the exchange unit is received and approved by us and the relevant manufacturer.
• Please note, surcharge refunds often take an average of 6 to 8 weeks to be approved by the manufacturer.
• Acceptance of the exchange part is at the manufacturer's discretion, based on the part being fit for reconditioning.
• All surcharges and exchanges are subject to our terms and conditions.

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

91164150100

The product you are viewing cross references to these numbers

Door Handle Triggers easy to change keeping your existing door handles and locks in SILVER. Fits Left OR right side. Sold as each.



Fits:
Porsche 911 1965-89
Porsche 964 1989-94

Please note: this is only part of the handle (No 15 on diagram). It requires to be changed over with existing trigger.

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

3607709112

The product you are viewing cross references to these numbers

HD sport front strut top mount. SET OF 2. 85 Shore rating 

Fits:
Porsche 911 / 912 / 930 / 914 All 1969-89
Will not fit SWB cars

High Density front strut mounts for your 911/914 not only replace tired factory rubber pieces, but return better handling and ride quality without being overly stiff. At 25% more stiff than stock, these are a great compromise, allowing the front suspension to maintain better alignment and geometry over bumps and around corners thanks to their increased stiffness. Still at home on a race track, these will ride with a feel closer to factory than that of our more track oriented full camber plate and monoball setups.

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

91134101800

The product you are viewing cross references to these numbers

HD Complete trailing arm bushing kit. Including installation tools 
Fast road and track 85 Shore rating 

Fits:
Porsche 964

Restore and maintain proper rear suspension geometry by returning your trailing arm play to factory standards with this kit which includes:
- Rubber bushings for two (2) 964 rear trailing arms
- Brand new aluminum bushing center sections
- Bushing press tool
- Lubricant for a quiet and easy finished installation

Our new High Density line now offers an alternative to purchasing expensive new rear trailing arms for your 964. This rear kit includes everything you need to remove and replace your original rubber bushings while providing a 25% increase in stiffness.

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

96433102100

The product you are viewing cross references to these numbers

HD trailing arm bushing.



Fits:
Porsche 944
Porsche 924

High Density trailing arm bushings for the 944 and 924s can both eliminate clunks from failing factory units and restore proper suspension geometry in your street or track car. Featuring an increased stiffness of 25% over OEM parts (90133102101), these are the ideal replacement for either failed or aging stock rubber units. These bushings locate rear trailing arms better under the sustained loads often experienced on track and in the rigors of everyday driving.

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

95133102101

The product you are viewing cross references to these numbers

HD Rear subframe bushing. Racing version
Complete set (4 pcs). 2 sets needed for one car.

Fits:
Porsche 993 1995-98 all models

Increase rear end stability and extend the life of your alignment with High Density subframe mounts. Factory units can cause rear ends to become more 'twitchy' and nervous, especially under high suspension loads, especially as they begin to fail. These bushings are not only responsible for holding the entire rear subframe to the shell, but for locating it in relation to the body and other suspension components. This means that even if they have not totally fallen apart the stock, soft mounts can often allow the entire rear suspension to shift and realign itself and as a result your entire car. Made from heavy duty high durometer rubber which features a 25% increase in stiffness over OE units, our High Density bushing kit includes the aluminum inner core and outer casement making them a plug and play solution for your 993. Enjoy a more planted rear end and stop living at the alignment shop with this full rear subframe kit.

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

99333105100

The product you are viewing cross references to these numbers

Street rear track rod bushings.
Price is EACH. (8 Required if you are changing all the bushes)

Fits:
Porsche 993 1995-98 (all) REAR

Street rear track rod bushings will bring back the OEM feel in your 911 that may have been lost due to worn out bushings. Track Rods are one of the most critical pieces of a 993 rear suspension as these rods locate the rear spindle assembly. This means a worn bushing can not only cause an even twitchier rear end, but they can negatively affect camber and caster changes through the suspension's range of motion.

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

99333104301

The product you are viewing cross references to these numbers

HD trailing arm bushing kit.
Comes as a complete kit, (1) per car with bushings for both rear sides. replacement for OE 90133105900



Fits:
Porsche 911 / 912 / 930 1965-89

High Density trailing arm bushings for the 911 can both eliminate clunks from failing factory units and restore proper suspension geometry in your street or track car. Made from 25% higher durometer than OEM (901.331.050.00) parts, these are the ideal replacement for either failed or simply aging stock rubber units. These bushings locate rear trailing arms better under the sustained loads often experienced on track and in the rigors of everyday driving.

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

90133105900

The product you are viewing cross references to these numbers

Racing version silent blocs for spring plate
Sold in sets of (4), enough for both sides of one car.



Fits:
Porsche 911/912/930 ALL 1965-89

Gain back ride quality and rear end stability with High Density Rear Spring Plate Bushings for your 911. Under prolonged use, especially when driven hard, the OEM bushings can break down allowing more slop in the rear suspension. If neglected long enough or driven under heavy load enough, these bushings will eventually deform allowing the spring plate to contact the cover plate. Replacing your factory bushings with our 25% stiffer units will allow full and smooth articulation of the spring plate, thus improving the ride quality and performance of the legendary rear end in your classic 911. Featuring a higher, "sport" durometer these rubber mounts are a great compromise between soft factory mounts and solid/spherical bearings often used to replace them.

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

90133300309

The product you are viewing cross references to these numbers

Heavy duty transmission bushing for Tiptronic gearboxes.
Sold as a set with (2) bushings included per kit to complete a single car.
Type: Racing / Motorsport

Fits:
Porsche 996 C2 / C4 / C4S 2002-2005 TIPTRONIC only
Porsche 996 Turbo 2001-2005 MANUAL & TIPTRONIC
Porsche 996 GT3 MKI & MKII 2000-2005 MANUAL only

Porsche 997 C2 / C4 / C2S / C4S TIPTRONIC only
Porsche 997 Turbo MKI 2006-2009 MANUAL & TIPTRONIC
Porsche 997 Turbo MKII 2010-2013 MANUAL only
Porsche 997 GT3 MKI & MKII 2007-2013 MANUAL only


HD transmission mounts replace your OEM transmission carrier bushings with our 25% stiffer bushings**. These units install the same as factory bushings and will eliminate clunks and driveline slop often associated with original rubber units. These high quality units feature aluminum center bushings and splined outer races filled with harder durometer rubber for perfect fitment and long service life. A perfect answer for those who want less driveline play but don't want harshness associated with semi solid and solid mounts.

Fits inside Porsche OE part 99737503303, or 99637503303

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

99737503303

The product you are viewing cross references to these numbers

HD front control / A-arm bushing kit.
SET OF 4 One set per car.  85 Shore rating 



Fit:
Porsche 911 / 930 1969-89
Porsche 914 1970-76


High Density bushings for Porsche 911 and 914 front A-Arms are a direct replacement for your old rubber bushings. Eliminate steering slop brought on by 40+ year old rubber and improve suspension geometry under all conditions with our 25% stiffer HD bushings. Due to the large surface area inherent in the design of the 911 and 914 torsion bar based control arms these are particularly important to achieving your car's potential both on and off the track. Sold as a complete set and machined out of a tougher rubber compound, these are the perfect compliment for any street or track setup.

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

91134190100

The product you are viewing cross references to these numbers

Lower control arm eccentric centre solid bushing. 
Price is EACH



Reduces caster changes under load
Allows easier, faster and more precise suspension adjustment 'Bolt in' solution; fits factory control arm and requires no further modifications

Fits:
Porsche 986 Boxster
Porsche 996 1997-05

High Density Thrust Arm Bushing Kit for the 996 and 986 Boxster is a great way to further perfect your suspension setup. These bushings offer the benefits of a harder durometer without the noise and ride harshness associated with solid aluminium bushings. A great option for dual use street/track vehicles that want another measure of adjust ability and stability without sacrificing ride quality.
25% increase in durometer

Material:
6082-T6 Aluminum
When using in 997/987 requires spacers/shims

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

99634105319

The product you are viewing cross references to these numbers

HD Semi-solid engine mount set. Fits to existing engine or gearbox mount shell.
One kit includes 2 halves of mount, (2 kits required per car).

Fits:
Work as engine mounts in 1965-1989 911/912/930
Work as transmission mounts in 1972-1986 911/912/930 (915/930 Transmission Only)

Fits to number 8 on the diagram.

High Density engine/transmission mounts are the perfect compromise between stock rubber and our Semi-Solid mounts. Their heavy duty 25% higher durometer rubber construction makes them ideal for performance oriented cars, but still allows absorption of vibrations and noise associated with solid mounts. Installs in stock motor mount or transmission mount hangers replacing worn out factory rubber.

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

91137504306

The product you are viewing cross references to these numbers