OE Match

Fits:
Porsche 986 Boxster 2.5ltr - 1997 to 1999 Engine Code M96.20
Porsche 986 Boxster 2.7ltr - 1999 to 2004 Engine Code M96.22 / M96.23
Porsche 987 Boxster 2.7Ltr -  2005 to 2008 Engine Code M96.25

and

Fits:
Porsche 993 Carrera 4 - 1994 to 1997
Porsche 993 turbo - 1994 to 1997
Porsche 993 - 1994 to 1997 cars with M030 (Sport type chassis) 

Drop link kit, Front and Rear. 
Kit Includes
Front drop Link x 2
Rear drop link x 2

and

Fits:
Porsche 993 Carrera 2 - 1994 to 1997

Engine cylinder head inlet valve kit.
Kit contains inlet valve x 6

Fits:
Porsche 911 T / E / S 2.2ltr - 1970 to 1971
Porsche 911 T / E / S 2.4ltr - 1972 to 1973
Porsche 911 2.7 Carrera MFI - 1973 to 1976
Porsche 911 / S 2.7ltr CIS - 1974 to 1977

Diameter - 46mm

Engine cylinder head exhaust valve kit - OE Match
Diameter - 40mm
Kit contains exhaust valve x 6

Fits:
Porsche 911 T / E / S 2.2ltr - 1970 to 1971
Porsche 911 T / E / S 2.4ltr - 1972 to 1973
Porsche 911 / S 2.7ltr - 1974 to 1977
Porsche 911 2.7 Carrera - 1974 to 1976

The gearbox carrier is suitable for the 915 gearboxes in the F-model as well as G-model. The steel part is a faithful reproduction according to modern manufacturing standards. The holder can be used for vehicles from 1972 to 1986. 

The large washers are for the engine and transmission bearings on the Porsche 911 F/G model. Also called plates at Porsche, they sit on the top and bottom of each engine mount/transmission bearing. The engine mounts for the Porsche 911 F and G models are reproduced in outstandingly good quality.

Fits: Porsche 911 1972- 86 (inc Sportomatic models (SPM)) 

Kit Contains

• Sunroof seal felt - Long x 1
• Sunroof seal felt - Short x 1
• Sunroof seal rear - Rubber x 1
• Sunroof felt x 1
• Sunroof side felt x 2

Fits:
Porsche 911 - 1965 to 1989

Please Note - For 911 from 1965 to 1973 and 964 / 993
91156440901 and 91156440900 not used

This kit includes the front and rear velvet strip, the rear sealing rubber and the three sealing strips. Brittle seals and water ingress into the cabin are now a thing of the past with this kit. 

Fits:
Porsche 911 1970-86 (915 Gearbox)
Porsche 930 Turbo 3.0ltr 1975-77 (915 Gearbox)

Worn rocker arms retard cam timing and rob the engine of power. These are the latest heavy duty, 930 rockers for optimum reliability.
To be used with standard camshafts.

Fits:
Porsche 911 1965-89
Porsche 964 1989-94
Porsche 914-6

Why Replace This Part?
Worn or fatigued rocker arms can lead to improper valve lift or seating, reduced compression, misfires, elevated emissions, and may affect overall engine reliability. Upgrading to a high-quality OE-match rocker arm restores the integrity of the cam-to-valve train and helps maintain optimal engine performance and longevity.

Rocker arm adjuster and securing nut set. Porsche 911 1965-89 / 964 / 914



Kit Includes
Adjuster Screw x 12
Adjuster Securing Nut x 12

Fits:
Porsche 911 1965-89
Porsche 964 1989-94
Porsche 914-6 1970-76

Contains rocker shaft x 12
Note: Please do not exceed factory torque spec of 18Nm

Fits:
Porsche 911 1965-89
Porsche 930 (911) 1975-89
Porsche 964 1989-94
Porsche 965 (964) Turbo 1989-94
Porsche 914-6 1970-76

SET OF 12 valve guides - standard. Inlet x 6 and exhaust x 6.

This is the standard valve guide used in early air-cooled Porsche 911/930 cylinder heads. It’s a plain (non-hydraulic) guide that locates the valve stem in the head; when worn it causes oil burning, loss of compression and poor valve seating — so they’re commonly replaced whenever heads are rebuilt.

What the part is (technical data / dimensions)

Application: Porsche 911 / 930 from about 1965–1989 (varies slightly by model and year; early cars both intake & exhaust, later years sometimes exhaust only). Standard size (typical OE): ID ≈ 9.00 mm, OD ≈ 13.06 mm, length ≈ 51.2 mm.        

Fits:Porsche 911 1965-1968 2.0L / 912 SWB (F)Porsche 911 1968-1973 2.2L / 2.4L / 2.7L RS LWB (F)Porsche 911 1974-1977 2.7L / 1976-77 3.0 CarreraPorsche 911 1978-1983 3.0L / SCPorsche 911 1984-1986 3.2LPorsche 911 1987-1989 3.2L G50Porsche 911 1975-1977 3.0L Turbo (930)Porsche 911 1978-1989 3.3L Turbo (930)

Why these guides should be replaced

Valve guides are a wearing item. Replace them when any of the following occur or when you rebuild the engine head.Excessive valve stem play — worn guide ID internal diameter lets the valve rock and misalign with the seat , poor sealing, reduced compression and power.Oil consumption / smoking — worn guides allow oil to wick down the stem into the combustion chamber, causing blue/grey smoke and fouled plugs.Hard starting, rough idle, misfire — poor sealing / valve timing irregularities from misaligned valves.Valve wobble that leads to premature valve stem wear or valve seat damage — once stems or seats are damaged you need deeper surgery.If a guide is cracked, broken, or has excessive ovality — must be replaced.Whenever you remove and refinish seats / replace springs / do a full head rebuild — replacing guides at that time is cheap insurance and ensures correct alignment. 

Inner diameter 9,00 mm
Outer diameter 13,06 mm
Total Length 51,20 mm

Click 'Zoom in' for large parts diagram.
Diagram Ref No 2 and 2A.