专业工具

发动机支架用于发动机支架。

#北环赛道#

适合：
保时捷 356
保时捷 911 912 F/G
保时捷 930
保时捷 914
保时捷 964
保时捷 993
保时捷 996 turbo/GT2/GT3
保时捷 997 turbo/GT2/GT3
吸料管外径D=60mm

参考编号：
00072120100, 000.721.201.00, 000 721 201 00, P201

为了改装您的保时捷发动机，我们提供此发动机支架。法兰表面与悬臂一起连接到安装轴，可安全且同时轻松将发动机连接到滚动发动机支架上。或者，您可以使用发动机支架通过轴承座将发动机安装到工作台上。我们的计划中提供带和不带安装支架的所有经典保时捷的发动机支架。

注意：零件的颜色可能与所示颜色不同。

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

6898

您正在查看的产品与这些编号存在交叉引用关系

发动机支架用于发动机支架。

#北环赛道#

适合：
保时捷 996/997 Carrera
保时捷 986/987 Boxster
保时捷 987C Cayman
（不适用于 911 turbo 和 GT2/GT3 车型）

为了改装您的保时捷发动机，我们提供这款发动机支架。法兰表面与悬臂一起连接到安装轴，可确保发动机牢固且易于安装到滚动发动机支架上。或者，您可以使用发动机支架将发动机安装到工作台上，使用额外提供的轴承座。

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

6806

您正在查看的产品与这些编号存在交叉引用关系

发动机正时套件 - 适用于保时捷996 Turbo / 996 GT2 / 997.1 Turbo / 997.1 GT2 3.6ltr

该 8230 正时工具套件旨在将配备 4 凸轮 3.6L 发动机的保时捷 911 GT2 和 911 Turbo 上的所有 4 个凸轮轴锁定在其定时位置。允许更换两个凸轮链，同时保持发动机正时。

该套件还包括 2 个凸轮链预紧器

附加信息
• 应用包括：保时捷996 Turbo / GT2 和997.1 Turbo / GT2 (2001 - 2010)。
• 发动机代码应用包括：M97/70S、M97/70、M96/70SL 和M96/70E。
• 相当于OEM 9661、9661/1 和9401。
• 与适当的 DTi（千分表指示器）和支架一起使用，以准确设置凸轮轴位置 - 请参阅激光零件号 7687。
• 设计按照 OEM 说明使用

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

8230

您正在查看的产品与这些编号存在交叉引用关系

Engine timing tool kit - for Porsche 997

The 7512 Engine Timing Kit provides the essential tools required to check and set the engine timing on the Porsche 911 (996 3.6 08/2001 to 07/2005, 997 3.6 & 3.8), Boxster 986 (08/2002 to 2011).

Porsche Applications include: 911 (08/2001 to 2008), Boxster (08/2002 to 2011), Cayman (2006 to 2009).
Engine applications: M96/03, M96/05, M96/23, M96/25, M97/20, M96/24, M96/26, M97/01, M97/21, M97/22.
Equivalent to OEM tools 9685, 9686, 9595 & 9595/1.
Use in accordance with OEM instructions
Supplied in a blow mould storage case

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

7512

您正在查看的产品与这些编号存在交叉引用关系

Exhaust bolt repair kit for all Porsche 996/997 GT3s, GT2s, and TTs.



Avoid the headache of trying to drill out broken exhaust bolts on the GT3 engines.

A CNC milled plate indexes precisely off of the broken bolts and/or bolt holes. Using our uniquely designed Thumb Screws, the SR068 plate is locked in place (by threading a Thumb Screw over a broken bolt or by using a supplied bolt threaded through the SR068 Thumb Screw). With the included pilot drills and drill guides, the faulty bolt can be drilled out, producing a perfectly perpendicular and centered hole that if necessary can be chased with the supplied M8x1.25 tap.

Kit includes: aluminum fixture, drill bits, tap with extension, drill jigs/guides, Thumb Screws, and hardware in a sturdy storage case. Now also includes our SR065D drill guide.

适用于 Boxster / 996 / 997 Carrera 和 Cayman Gen1 1997-2009 的排气螺栓修理套件（非 GT3、GT2 或 TT 发动机）

#斯托姆斯基#

随着水冷发动机排气管螺栓断裂的报道越来越多，修复断裂螺栓的麻烦也越来越普遍。从简单的排气系统更新到发动机拆卸，各种任务都不断受到排气歧管螺栓断裂、生锈和断裂的困扰。在发动机还在车上的情况下，很少能准确地拆除断裂的螺栓，即使拆除后，这项任务也很耗时，如果不小心，可能会导致头部损坏或维修失误。STOMSKI RACING 针对这些问题的解决方案是 SR067，这套工具可让您轻松、准确、灵活地钻出断裂的螺栓 - 发动机仍在车内 - 节省时间和麻烦。CNC 铣削板可精确地定位断裂的螺栓和/或螺栓孔。使用我们独特设计的翼形螺钉，SR067 板可锁定到位（通过将翼形螺钉拧到断裂的螺栓上或使用提供的螺栓穿过 SR067 翼形螺钉）。使用附带的导向钻和钻孔导向器，可以钻出故障的螺栓，形成一个完全垂直且居中的孔，如果需要，可以使用附带的 M8x1.25 丝锥进行钻孔。

套件包括：阳极氧化铝固定装置、钻头、带延长杆的丝锥、钻夹具/导轨、翼形螺钉以及坚固的储物盒中的硬件。

现在还包括我们的 SR065D 钻孔指南。

适用于保时捷 GT3/GT2 的 GT3 凸轮正时装置 V2。

#斯托姆斯基#

无论您是想提前或延缓凸轮正时、升级凸轮，还是只是想以绝对精度设置任何 GT3/GT2 发动机上的凸轮正时，这都是完成这些任务的最精确的工具。无需满足于使用工厂工具完成的“足够接近”或“大致”设置。
STOMSKI RACING 的 GT3 凸轮正时装置为所有凸轮和设置提供绝对的准确性、无限的可调性和卓越的灵活性。
包括完整的装置，带有 ASME/ANSI 认证的刻度盘指示器和一个（12 毫米或 14 毫米）TDC 指示器，带行程计（SR092 或 SR093）。包括存储箱。

保时捷 996 / 997 的热交换器适配器

#斯托姆斯基#

M96/M97 油冷却液热交换器紧凑、高效设计已被证明除了用于发动机冷却之外，还可用于其他用途。通过远程安装 M96/M97 交换器，可以降低变速箱和/或转向齿条的温度，并显著延长这些部件的使用寿命。

STOMSKI RACING 的 M96 热交换器适配器可实现便捷的远程安装，并包括您选择的 -6 或 -8 AN 配件。这款高品质适配器板采用 6061 铝材 CNC 加工而成，阳极氧化处理，使用寿命长，并包括密封件和硬件。

插孔

#北环赛道#

适合：
自 1985 年 8 月起的保时捷 944
保时捷 964
保时捷 968
保时捷 993
保时捷 996 Carrera 2/4 / 996 Turbo
保时捷 997 Carrera 2/4 / 997 Turbo
保时捷 986 Boxster
保时捷 987 Boxster
保时捷 987C Cayman


如果您想在通常的千斤顶位置举升车辆，就不能绕过适配器。只有这样，车辆才能安全稳定地升起，不会有滑落的风险，并且车身底部保护/油漆也受到保护。由于原装支架中的销钉几何形状，该适配器可以旋转，并牢固地固定在车辆上。

优点：
• 采用 7000 铝合金，强度高
• 防止刮伤底盘保护装置/油漆
• 可使用通用千斤顶进行安全顶升
• 锥形轴颈底座具有锁定功能
• 几何形状适合于所提及的保时捷车型。

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

1154

您正在查看的产品与这些编号存在交叉引用关系

Oil pressure relief plug extractor Porsche 911 / 964 / 993 / 996 / 997



Tolerance between the pressure relief plug and its galley are very close, and the slightest bit of gunk, corrosion, or bur will cause the plug to freeze up in the oil passage. A magnet is rarely powerful enough to overcome the seized plug, and leaving it in place is never an option.
Using STOMSKI RACING's Oil Pressure Relief Plug Extractor makes the task of removing the stuck plug a breeze, and allows you to ensure clean oil passages, and a properly operating bypass system.

The collet-based tool slides easily into the open end of the seized plug and a simple turn or two of the internal socket head cap screw expands the tool, grasping the plug to ensure easy removal.

Anodized Aluminum.

Rear main oil seal fitting tool Porsche Boxster and 911 M96/M97



Fits
Boxster/Cayman 1997-2008
Porsche 911 Carrera 1999-2008 (Excludes Turbo, GT3 and GT2 models)

Description of Tool
This is a 3D Printed tool for installing the Rear Main Seal on Porsche M96/M97 engines to the correct depth without damage to the seal. The tool is 3D printed from hard, black plastic and is very solid and durable. It is aimed at DIYers and hobbyists due to its low cost in comparison to the official Porsche tool, but would be well suited to small independent garages as the tool can be reused many times without damage.

How to use
Care must be taken when using this tool as although it is designed to make the installation of the seal as easy as possible, it is still possible to damage or incorrectly install the seal if care is not taken to install the seal properly. We accept no responsibility for incorrect usage of the tool and possible damage to the seal or engine of the vehicle. We advise you to always confirm with a digital calipers or other measuring device to make sure the seal is installed at the correct depth.
To use this tool you will also need 4 M10 X 75mm bolts and 4 washers. This is to allow for the extra thickness of the tool, and to spread the force from the bolts across the surface of the tool.
The seal must first be correctly orientated and then gently located into the opening around the crankshaft. To do this, leave the blue plastic ring in place and place the seal over the end of the crankshaft. Then push the seal on gently so that the end of the crankshaft pushes the blue ring out of the seal and the seal gets pushed onto the outside of the crankshaft.
Next place the RMS fitting tool over the seal and thread each of the 4 bolts into the crankshaft, through the holes in the tool. Make sure to orientate the tool so that the cut-out for the flywheel guide pin in the crankshaft lines up with the pin. Screw each bolt in slowly until they just about make contact with the face of the tool. From this point on the seal will start to be inserted into the engine.
Turn each bolt a quarter turn at a time, turning all 4 a quarter turn before tightening the first one again, and continuing the cycle. It is very important that the bolts are tightened small amounts, one at a time to make sure that the seal is inserted straight and not at an angle which will damage the seal.
Repeat this until the face of the crankshaft comes into contact with the inner face of the tool and it will not push the seal in any further. Remember that the tool is plastic so excessive force at the point will possibly damage the tool and push the seal in too far.
The 4 bolts can now be unscrewed and fully removed from the crankshaft. The tool can then be removed. It may be a slightly tight fit, and if it is difficult to remove by hand then there are slots in the sides of the tool to allow a screwdriver or prying tool to grip the tool and remove it. If using the slots, be careful to apply even force to both sides to ensure that the tool does not come out at an angle and get stuck or potentially move the seal.
Once the tool and bolts are removed, visually inspect the seal to make sure there is no damage. Then, use a ruler, digital callipers or depth gauge, check the depth of the seal. It should measure 13mm, from the face of the crankshaft to the face of the seal. As long as the tool was used correctly and is suitable for your engine, the seal will be installed at the right depth.
These instructions are only intended as a rough guide, you should always check a workshop manual or research online to ensure the part is being installed correctly. Using this tool requires some practical knowledge so if you are not confident in your abilities please do not attempt to install the seal yourself.

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

0PB105249

您正在查看的产品与这些编号存在交叉引用关系

后主油封安装工具。

#科布伦茨#

适合

保时捷 986 Boxster 2.5lrr / 2.7ltr
保时捷 986 Boxster S 3.2 升
保时捷 987.1 Boxster / Cayman 2.7 升
保时捷 987.1 Boxster / Cayman 2.9 升
保时捷 987.1 Boxster S / Cayman S
保时捷 987.1 RS Spyder
保时捷 996 Carrera 2 / Carrera 4
保时捷 996 Carrera 4S
保时捷 997.1 Carrera 2 / Carrera 4
保时捷 997.1 Carrera 2S /Carrera 4S

此专用维修工具是为了正确安装后主油封而开发的。
尝试使用任何其他方法完成此任务都有可能因后主密封损坏而导致发动机损坏

德国制造

Time-Sert™ thread repair kit for SR065/SR067/SR068 for Porsche 911 / Boxster / 996 / 997



For exhaust port studs on 911, Boxster, 996/997 or GT3 heads where the threads have been pulled, or to recover from an already improper repair, we have developed this Time-Sert(tm) kit so you may use our SR065, SR067, SR068 or SR069 tools to insert a Time-Sert and save an otherwise ruined head. In addition to the standard Time-Sert(tm) parts (short P drill, counter-bore, tap, insert tool, and 5 short inserts), our kit also includes a full length P drill, two drill jigs/bushings to guide the P drill and tap in our SR065, SR067, or SR068 fixtures, 5 full length inserts, and 5 studs.

Time-Sert(tm) is a registered trademark of TIME FASTENER COMPANY

Timing chain starp / support for Porsche 911

When assembling the case halves on the 911 engine STOMSKI RACING's SR222-GT3 Timing Chain Strap will prove instrumental in supporting the chain to allow easier mating of the halves. Proper length, radius bend, tension, and quality steel insure that this tool will provide reliable and consistent support for all your engine builds.

fits
• SR222-GT3 for the 996/997 GT2, GT3, and TT engines.

Vario cam sprocket tool for Porsche 996 / 997 GT3/TT/GT2



STOMSKI RACING's version of this tool works on Vario intake cams on the GT2, TT, and GT3 engines. This tool replaces the factory tool P9653. Additional refinements to this tool ensure that while torquing the 16mm hex cam sprocket bolts, your tool is securely bushed and supported in the center of the tool, and thus will not slip off or round off the bolts. Black oxide finished hardened steel.