斯托姆斯基赛车队

996/997 GT3 Control arm monoball assembly for Porsche 986 / 987 / 996 / 997  Price is each



Whether for a dedicated race car, or for a suspension upgrade on your street GT3, these inner Control Arm Monoballs are the ultimate upgrade or replacement. CNC machined from aircraft quality aluminum, the housing contains the BEST aerospace monoball available. Stainless steel bushings, and Jet nuts complete the package to make these assemblies your only choice for upgrading or replacement. Seals are included for the ultimate upgrade. OEM outer control arms also available.

For 986/987/996/997.



相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

SR040

您正在查看的产品与这些编号存在交叉引用关系

Front brake caliper adapter for Porsche 911 84-89 with 996/Boxster calliper



These precisely machined adapters convert your standard 911 front struts (with 3.5" bolt spacing) to allow you to mount Boxster calipers while running the beefy 1984-89 Carrera vented rotors. EXTREME stopping power, GREAT looks, and all the while allowing you to run 15" Fuchs or larger with stock hubs.

Kit comes complete with TWO adapters and high quality fasteners necessary for a quick conversion.

Anodized aluminum.

Requires the calipers to be swapped left to right/right to left, and thus inverted.

Brake caliper adapter for Porsche 993 Carrera to mount Big reds



These precisely machined adapters convert your standard 911 front struts (with 3.5" bolt spacing) to allow you to mount 993 Twin Turbo calipers.

Kit comes complete with TWO adapters and high quality fasteners necessary for a quick conversion.

Anodized aluminium.
Requires 993 Turbo brake rotors and non-stock hubs.

凸轮/动力转向阻断板适用于保时捷 911 / 964 / 993

#斯托姆斯基#

使用此板封闭 993 的凸轮塔上的动力转向泵开口，或封闭涡轮增压器和早期 911 的凸轮塔上的油泵和喷射泵开口。此板是定制设计的，适用于库存和非库存凸轮。

阳极氧化铝。

适用于 1998 年之前的 911。

单独出售。

适用于保时捷 911 1974-89 的制动卡钳适配器，适合 Boxster S / 996 卡钳

#斯托姆斯基#

这些精密加工的适配器可转换您的标准 911 前支柱（螺栓间距为 3.5 英寸），以便您安装 996（NA）或 Boxster S 卡钳。

套件包含两个适配器和快速转换所需的高质量紧固件。阳极氧化铝材质。

需要 996 个转子和非库存轮毂。

适用于保时捷 911 1974-89 的前制动卡钳适配器，适合 996 Turbo 卡钳

#斯托姆斯基#

这些精密加工的适配器可转换您的标准 911 支柱（螺栓间距为 3.5 英寸），以便您安装 996 Twin Turbo 卡钳。

套件配有两个适配器和快速转换所需的高质量紧固件。

阳极氧化铝。

需要 996 TT 转子和非库存轮毂。

996 / 997 GT3 凸轮挡板

#斯托姆斯基#

当 GT3 和 Turbo vario 升程进气凸轮被替换为任何 996/997 Mezger 发动机上的静态正时赛车凸轮时，请使用这些高品质铝制盖替换笨重的工厂式凸轮盖。

直接替换所有 GT3 Cup 和 RSR 引擎以及所有调谐器应用程序。

按一对/套（2）出售。

Time-Sert™ thread repair kit for SR065/SR067/SR068 for Porsche 911 / Boxster / 996 / 997



For exhaust port studs on 911, Boxster, 996/997 or GT3 heads where the threads have been pulled, or to recover from an already improper repair, we have developed this Time-Sert(tm) kit so you may use our SR065, SR067, SR068 or SR069 tools to insert a Time-Sert and save an otherwise ruined head. In addition to the standard Time-Sert(tm) parts (short P drill, counter-bore, tap, insert tool, and 5 short inserts), our kit also includes a full length P drill, two drill jigs/bushings to guide the P drill and tap in our SR065, SR067, or SR068 fixtures, 5 full length inserts, and 5 studs.

Time-Sert(tm) is a registered trademark of TIME FASTENER COMPANY

Stomski Racing SR024 Through bolt o-ring installer with sleeve for Porsche 911



Based on the factory P9511 tool, STOMSKI RACING's version of this tool incorporates a brass cap and a double-ended stainless steel sleeve to install the o-rings on the crankcase through-bolts of the 3.6 and later cases (but possibly can be used on some other 911 engines). By using the included brass cap to protect the delicate o-ring from getting cut on the threads of the bolt, you then use the "thin" end of the sleeve to slide the o-ring over the brass cap onto the shank of the through-bolt. Once the o-ring is clear of the threads, remove the SR024 brass cap and flip the SR024 stainless steel sleeve over and use the blunted end to securely and gently seat the o-ring in the recess on the 3.6 case.

Through bolt o-ring installer for Porsche 911



Installing O-rings on the through bolts for a 911 engine case often slices the rings on the threads of the bolt, leading to ripped seals at best, or a leaky engine at worst. Use this cap to protect the O-ring and to insure a factory quality seal. Precisely machined from quality brass.

保时捷 911 的 TDC 指示器

#斯托姆斯基#

为了确保最高的计时精度，应检查所有发动机的真实 TDC，以确认皮带轮 TDC 标记相对于实际 TDC 的准确性。此工具拧入火花塞孔，并提供活塞相对于皮带轮/曲轴的位置的机械指示。通过旋转曲轴并接触/撞击活塞至死点 BTDC，然后以相反方向旋转发动机并再次接触/撞击活塞至死点 ATDC，在度盘、皮带轮或我们的 DigiDix-SR095 上记录两个测量值，您可以计算出纯 TDC。

适用于 12 毫米或 14 毫米火花塞孔。

分开售卖。

TDC indicator with travel gauge for Porsche 911



For engines where you do not have to use our "dead-stop" TDC Indicator (SR022/23), use our easy to use, highly accurate TDC Indicator With Travel Gauge to measure the exact position of the piston. Precisely manufactured from 6061 Aluminum and hard-coated for extra wear resistance, these indicators include ASME/ANSI certified travel gauges for proven accuracy. Not recommended for use on the hemispherical heads on air-cooled 911s.

Available for either 10mm, 12mm, or 14mm spark plug holes.

Sold separately.

Sprocket registration pin puller for Porsche 911



This unique tool allows you to easily pull the cam timing sprocket registration pin. No more yanking on the factory tool, hurting your fingers, or pulling the sprocket off the end of the cam shaft. Use this precisely machined slide hammer to delicately pull the pin.

Oil pressure relief plug extractor Porsche 911 / 964 / 993 / 996 / 997



Tolerance between the pressure relief plug and its galley are very close, and the slightest bit of gunk, corrosion, or bur will cause the plug to freeze up in the oil passage. A magnet is rarely powerful enough to overcome the seized plug, and leaving it in place is never an option.
Using STOMSKI RACING's Oil Pressure Relief Plug Extractor makes the task of removing the stuck plug a breeze, and allows you to ensure clean oil passages, and a properly operating bypass system.

The collet-based tool slides easily into the open end of the seized plug and a simple turn or two of the internal socket head cap screw expands the tool, grasping the plug to ensure easy removal.

Anodized Aluminum.

Heat exchanger tester for Porsche 996 / 997



Some M96/M97 engines are experiencing oil-to-coolant intermixing. While there are potentially several sources of intermixing, faulty engine mounted oil-to-coolant heat exchangers are a major source. Now, with STOMSKI RACING's M96 Heat Exchanger Tester, you can confirm if your exchanger is faulty and needs replacing, or whether the source of the contamination is elsewhere. This high-quality tool is CNC machined from 6061 aluminum, anodized for years of service, and comes complete with all gauges, seals and hardware.

Leak-down / compression adapter for Porsche 911



You no longer need to fight or snake a flexible rubber hose blindly through the valve cover and into the cylinder head to hook up a compression or leak down gauge on the 911 engines (or other engines with remote spark plugs). Simply insert this unique tool into the spark plug hole of the cylinder head and attach your gauge. Precisely machined from high quality stainless steel or hard-coated aluminum.

Available in two sizes based on spark plug thread/diameter.

Sold separately.